TERMIUM Plus^®

Record 1,  Textual support,  English

Record number: 1, Textual support number: 1 CONT

... the three-part can consists of a base, body and lid while in two-part cans the body and base are made from a single piece of metal. In a three-part can, the body seam is electrically welded but the lid on all cans is held in place by a double seam.  3, record 1, English, - three%2Dpiece%20can

Record 1,  Textual support,  French

Record number: 1, Textual support number: 1 CONT

Du point de vue technologique, on distingue deux types de boîtes dans le domaine alimentaire : la boîte trois pièces composée d'un corps, d'un fond et d'un couvercle; [et] la boîte deux pièces composée d'un corps et d'un fond (monobloc) avec un couvercle de fermeture.  4, record 1, French, - bo%C3%AEte%20trois%20pi%C3%A8ces

Record 1,  Textual support,  Spanish

Record 2,  Textual support,  English

Record number: 2, Textual support number: 1 CONT

This Standard specifies angle beam ultrasonic examination mainly intended for the detection of longitudinal imperfections of the seamless steel tubes and weld seam of the electric resistance welded steel tubes with an outside diameter greater than or equal to 9. 0 mm, with a thickness greater than or equal to 1. 0 mm and with a thickness-to-outside diameter percentage smaller than or equal to 20%.  2, record 2, English, - angle%20beam%20ultrasonic%20examination

Record number: 2, Textual support number: 1 OBS

angle beam ultrasonic examination: term extracted from the “Glossaire de l’énergie nucléaire” and reproduced with permission of the Organisation for Economic Co-operation and Development.  3, record 2, English, - angle%20beam%20ultrasonic%20examination

Record 2,  Textual support,  French

Record number: 2, Textual support number: 1 OBS

contrôle par ultrasons en ondes transversales : terme extrait du «Glossaire de l’énergie nucléaire» et reproduit avec l’autorisation de l’Organisation de coopération et de développement économiques.  2, record 2, French, - contr%C3%B4le%20par%20ultrasons%20en%20ondes%20transversales

Record 2,  Textual support,  Spanish

Record 3,  Textual support,  English

Record number: 3, Textual support number: 1 CONT

Steel battery wells are of heavy gauge galvanized steel construction. The well is of one piece, formed and seam welded. The cover has a raised center which allows for efficient water drainage. It is completely removable.  1, record 3, English, - battery%20well

Record 3,  Textual support,  French

Record 3,  Textual support,  Spanish

Record 4,  Textual support,  English

Record number: 4, Textual support number: 1 CONT

Unlike two-piece cans, three-piece cans cannot be die-necked repeatedly to form a smooth neck because of the non-homogeneity of their welded seam.  1, record 4, English, - smooth%20neck

Record 4,  Textual support,  French

Record number: 4, Textual support number: 1 CONT

Avec la diminution du diamètre du col des boîtes-boisson (col 202), le procédé de formage par «die necking» s'est particulièrement bien développé ces dernières années [...] Il existe principalement deux variantes de ce procédé : La première [...] consiste à former un col à gradins. [...] L'autre variante consiste à former un col lisse.  1, record 4, French, - col%20lisse

Record 4,  Textual support,  Spanish

Record 5,  Textual support,  English

Record number: 5, Textual support number: 1 CONT

Manufacturers of canvas or high frequency welded seam vinyl.  1, record 5, English, - high%20frequency%20welded%20seam

Record 5,  Textual support,  French

Record number: 5, Textual support number: 1 CONT

Veste [...] Couture soudée haute fréquence. Capuche enveloppante avec visière et cordon de serrage [...] Pantalon : Couture soudée haute fréquence.  1, record 5, French, - couture%20soud%C3%A9e%20haute%20fr%C3%A9quence

Record 5,  Textual support,  Spanish

Record 6,  Textual support,  English

Record number: 6, Textual support number: 1 CONT

A real-time digital video-image-processing system contributes to the automation of weld-seam tracking. The tracking system makes no contact with the seam. A small television camera views the seam just ahead of the point currently being welded. The welding arc provides the illumination. Periodically, a frame grabber digitizes the video image and stores it in a computer memory as gray-scale values. The seam is located by analyzing Hough-transform arrays of derivatives of digitally-filtered image data. The information on the location and orientation of the seam is used as feedback by a welding robot to correct deviations of the electrode from the seam as welding continues.  1, record 6, English, - real%2Dtime%20digital%20video%2Dimage%2Dprocessing%20system

Record 6,  Textual support,  French

Record 6,  Textual support,  Spanish

Record 7,  Textual support,  English

Record number: 7, Textual support number: 1 CONT

Emitters usually have close, uniform spacings(e. g. 0. 025-0. 60 m) along a lateral line and emitters are either simple orifices, long path or labyrinth flow paths or a combination. Emitters may be embossed within the welded seam of the tape or they may be separate, pre-molded devices installed during fabrication.... The labyrinth emitter, designed with long intricate passageways, will create turbulent flow at normal operating pressures and is often called a turbulent or turbulent-path emitter. The turbulent flow resists plugging by allowing the flow path to be as large as possible and preventing small particles from settling or becoming lodged in the passageway. Flow rates from turbulent path emitters are also relatively insensitive to temperature fluctuations, thus avoiding a major cause of nonuniform water application under field conditions. Currently, most point source emitters utilize turbulent flow paths to control the application of water on tubing and some tapes, and are highly recommended for wine grape irrigation in the PNW.  2, record 7, English, - large%20turbulent%20flow%20labyrinth%20emitter

Record 7,  Textual support,  French

Record number: 7, Textual support number: 1 CONT

L'organe de distribution d'un réseau de micro-irrigation par goutte à goutte est le goutteur. Celui-ci peut être en ligne donc inséré sur la rampe ou en dérivation donc fiché dans la paroi de celle-ci ou relié par l'intermédiaire d'un petit tube appelé conducteur. On distingue des goutteurs à circuit court, des goutteurs à circuit long, des goutteurs à compensation de pression, des goutteurs turbulents à circuit court qui sont des cyclones miniaturisés, des goutteurs turbulents à circuit long, dit à chicanes ou labyrinthes.  1, record 7, French, - goutteur%20turbulent%20%C3%A0%20circuit%20long%20dit%20%C3%A0%20chicanes

Record 7,  Textual support,  Spanish

Record 8,  Textual support,  English

Record number: 8, Textual support number: 1 CONT

Welded cans are manufactured by one of two methods, wheel or wire welding. Both are variations of a forge-welding process.... Wire welding can accommodate the use of tin plate while wheel welding is best suited for tin-free steel, TFS. When using TFS, both methods require grinders to clean the edges to be welded so that they are free of oxides and chrome surface materials. Prior to side seam welding, the body blanks are formed into cylinders and tack-welded to maintain shape and proper relationship of the edges to each other.... Welded seams are used extensively for three-piece beverage, aerosol and food cans.  1, record 8, English, - wire%20welding

Record number: 8, Textual support number: 1 OBS

The wire weld system has been developed by Soudronic A.G. Switzerland.  2, record 8, English, - wire%20welding

Record 8,  Textual support,  French

Record number: 8, Textual support number: 1 OBS

Quant à la soudure du corps proprement dit de l'emballage trois pièces, si la technique classique de l'agrafage-soudage donne toujours satisfaction, d'autres procédés sont également utilisés maintenant. Soudure électrique par fil : couramment appliquée aux gros emballages.  2, record 8, French, - soudage%20%C3%A9lectrique%20par%20fil

Record number: 8, Textual support number: 2 OBS

soudure : Opération par laquelle on soude.  3, record 8, French, - soudage%20%C3%A9lectrique%20par%20fil

Record 8,  Textual support,  Spanish

Record 9,  Textual support,  English

Record number: 9, Textual support number: 1 DEF

Steel pipe made from sheets of steel curved into cylindrical shape with the edges welded together. The seams may form a spiral running around the circumference of the pipe with welding along the seam.  2, record 9, English, - spiral%20welded%20pipe

Record 9,  Textual support,  French

Record number: 9, Textual support number: 1 DEF

Tuyau d'acier fait de tôles enroulées de façon que les joints forment une spirale parcourant la circonférence du tuyau; le tuyau est soudé le long du joint.  1, record 9, French, - tuyau%20soud%C3%A9%20en%20spirale

Record 9,  Textual support,  Spanish

Record 10,  Textual support,  English

Record number: 10, Textual support number: 1 DEF

Steel pipe made from sheets of steel curved into cylindrical shape with the edges welded together. Field joints may be flanged, screwed, or welded. The seams may form a spiral running around the circumference of the pipe with welding along the seam.  2, record 10, English, - welded%20steel%20pipe

Record 10,  Textual support,  French

Record number: 10, Textual support number: 1 DEF

Tuyau fait de tôles d'acier dont les rebords sont soudés en spirale ou non.  1, record 10, French, - tuyau%20en%20acier%20soud%C3%A9

Record 10,  Textual support,  Spanish

Record 11,  Textual support,  English

Record number: 11, Textual support number: 1 OBS

in seam welding, the stationary electrodes are replaced by rollers to produce a continuous welded seam or joint.  1, record 11, English, - roller

Record 11,  Textual support,  French

Record number: 11, Textual support number: 1 OBS

soudage à la molette. C'est une variante du soudage par points (...) les électrodes sont remplacées par deux molettes (...) entraînées par un moteur et serrées l'une contre l'autre.  1, record 11, French, - molette

Record 11,  Textual support,  Spanish