TERMIUM Plus®

From: Translation Bureau

On social media

Consult the Government of Canada’s terminology data bank.

GATING SYSTEM [4 records]

Filter results by subject field Alphabetical list of terms

Filter results by subject field

Alphabetical list of terms

Record 1 2014-04-11

English

Subject field(s)
  • Plastics Manufacturing
  • Facilities and Equipment (Rubber)
DEF

An edge gate where the opening from the runner into the mold is located below the parting line or mold surface ...

CONT

A submarine gate penetrates through the steel of the cavity. When the mold opens, the part sticks to the cavity and shears the piece at the gate. A properly located KO [knockout] pin, using the flexibility of the plastic, ejects the runner and pulls out the gate. This type of gate is usually used in automatic molds.

OBS

[In] conventional edge gating,... the opening is machined into the surface of the mold. [In] submarine gates, the item is broken from the runner system on ejection from the mold.

OBS

submarine gate; tunnel gate: terms standardized by ISO [International Organization for Standardization].

French

Domaine(s)
  • Plasturgie
  • Installations et équipement (Caoutchouc)
DEF

Canal d'injection situé sous le plan de joint de façon que la carotte soit arrachée lors de l'éjection.

OBS

entrée sous-marine; entrée sous le plan; entrée sous le plan de joint : termes et définition normalisés par l'ISO [Organisation internationale de normalisation].

Spanish

Campo(s) temático(s)
  • Fabricación de plásticos
  • Instalaciones y equipo (Caucho)
DEF

Canal de inyección situado debajo de la superficie de unión, de manera que con la operación de eyección la mazarota se desprende.

CONT

Entrada de túnel o submarina. La entrada es separada de la colada al abrir el molde o por medio de una ruptura forzada en el momento de expulsar la pieza. La entrada de túnel es adecuada para una inyección lateral.

Save record 1

Record 2 - external organization data 2002-02-27

English

Subject field(s)
  • Scientific Research Equipment
  • Compartment - Canadian Nuclear Safety Commission
CONT

... framing tubes and solid-state imaging devices for use with cameras controlled in paragraph(b) as follows :(1) proximity focused image intensifier tubes having the photocathode deposited on a transparent conductive coating to decrease photocathode sheet resistance; gate silicon intensifier target(SIT) vidicon tubes, where a fast system allows gating the photoelectrons from the photocathode before they impinge on the SIT plate...

OBS

Regulation cited: Nuclear Non-Proliferation Import and Export Control Regulations.

Key term(s)
  • gate SIT vidicon tube

French

Domaine(s)
  • Matériel et équipement (Recherche scientifique)
  • Tiroir - Commission canadienne de sûreté nucléaire
CONT

[...] tubes à images et imageurs à semi-conducteurs destinés à être utilisés avec les caméras mentionnées au paragraphe b), comme suit : (1) tubes intensificateurs d'images avec mise au point sur proximité, dont la cathode photovoltaïque est déposée sur une couche conductrice transparente afin de diminuer la résistance de couche de la cathode photovoltaïque; (2) tubes intensificateurs vidicons au silicium et à grilles où un système rapide permet de séparer les photoélectrons de la cathode photovoltaïque avant qu'ils ne soient projetés contre la plaque de l'intensificateur vidicon au silicium [...]

OBS

Règlement cité : Règlement sur le contrôle de l'importation et de l'exportation aux fins de la non-prolifération nucléaire.

Spanish

Save record 2

Record 3 1998-02-02

English

Subject field(s)
  • Plastics Manufacturing
CONT

Insulated runner molds. A combination between a hot runner mold and a three-plate mold is called an insulated runner mold. The gating system is very similar to that of a three-plate mold except that the runners are very thick, at least 1 3/4in.(45mm) in diameter. There is no runner plate, and the backup plate and A plate are held together by latches. After the material is injected, the outside of the runner freezes but insulates the center, permitting the core to remain fluid at molding temperatures and act as a hot runner.

French

Domaine(s)
  • Plasturgie
Key term(s)
  • moule à canal isolé

Spanish

Save record 3

Record 4 1998-01-21

English

Subject field(s)
  • Plastics Manufacturing
CONT

... the gating system(which brings the hot plastic into the cavity) ;...

French

Domaine(s)
  • Plasturgie

Spanish

Save record 4

Copyright notice for the TERMIUM Plus® data bank

© Public Services and Procurement Canada, 2026
TERMIUM Plus®, the Government of Canada's terminology and linguistic data bank
A product of the Translation Bureau

Display options

Change the order of display of the official languages of Canada
Option to display the non-official languages (Spanish or Portuguese)
Display definitions, contexts, etc., on records

Features

GCtranslate (available on the Government of Canada network only)

Use this artificial intelligence prototype to translate Government of Canada content up to and including Protected B. Available to employees of selected departments and agencies only.

Writing tools

The Language Portal’s writing tools have a new look! Easy to consult, they give you access to a wealth of information that will help you write better in English and French.

Glossaries and vocabularies

Access Translation Bureau glossaries and vocabularies.

Date Modified: