TERMIUM Plus^®

Record 1,  Textual support,  English

Record number: 1, Textual support number: 1 CONT

There is an alternative between closed-and open-loop systems called standing column wells(SCWs). In a SCW, groundwater is pumped from the base of a deep well and directed to a heat exchanger.... A SCW consists of a long borehole mostly drilled in the bedrock and filled with groundwater... Typical installations use a PVC [polyvinyl chloride] pipe almost as long as the well within which a submersible pump is installed. In a conventional SCW, groundwater is pumped at the bottom of the well through a PVC pipe and returned below the dynamic level in the annular space of the borehole via a rejection pipe.... Before reinjecting the groundwater into the SCW, part of the flow rate can be diverted into a separate injection well. This process is called "bleed" and improves the system performance by attracting water from the undisturbed neighbouring ground through aquifer fractures. The bleed induces heat transfer by advection..., which improves significantly the thermal efficiency of the SCW.  2, record 1, English, - standing%20column%20well

Record 1,  Textual support,  French

Record number: 1, Textual support number: 1 CONT

Le fonctionnement des PCP repose sur l'utilisation de l'eau souterraine comme fluide caloporteur. L'eau est généralement prélevée à proximité de la surface à l'aide d'une pompe submersible et réinjectée à la base du puits. [...] Afin d'améliorer l'efficacité thermique des PCP en période de pointe, un procédé communément appelé «saignée» peut être employé. Cette méthode consiste à purger le PCP d'un faible pourcentage du débit de circulation, afin de stimuler un écoulement souterrain convergent vers le puits. Ce faisant, le renouvellement de l'eau contenue dans le PCP permet de stabiliser rapidement la température du fluide caloporteur à l'approche de la thermopompe.  3, record 1, French, - puits%20%C3%A0%20colonne%20permanente

Record 1,  Textual support,  Spanish

Record 2,  Textual support,  English

Record number: 2, Textual support number: 1 CONT

An ex-vessel steam explosion may occur if the primary system is breached by hot debris. Debris in the reactor outlet piping may fail the piping and fall onto the pump room floor or debris on the reactor vessel bottom may be blocked from flowing into the outlet piping if it freezes in the effluent piping nozzle muff structure. If this occurs, the debris will heat up on the reactor vessel bottom and eventually fail the bottom shield. The likely mode of failure of the bottom shield is collapse of the shield as a whole. If it collapses, the entire shield, as well as the molten debris, will fall into the pin room below the reactor vessel. The debris will then flow across the floor into the pump room. In either event, a large portion of the reactor fuel inventory will be deposited on the pump room floor. The pump room floor will be covered with water in many scenarios. A steam explosion may result when the debris enters this water.  1, record 2, English, - ex%2Dvessel%20explosion

Record 2,  Textual support,  French

Record number: 2, Textual support number: 1 CONT

La condition nécessaire à une explosion vapeur est le simple contact entre les deux fluides, mais les situations les plus énergétiques sont celles où les deux fluides sont mélangés avant que ne se déclenche la fragmentation. Dans les réacteurs à eau pressurisée de tels mélanges pourraient se former après la fusion du cœur lors de la relocalisation du corium en fond de cuve (explosion en cuve) et/ou éventuellement lors de la percée de la cuve et la chute du corium dans le puits de cuve (explosion hors cuve).  1, record 2, French, - explosion%20hors%20cuve

Record 2,  Textual support,  Spanish