TERMIUM Plus^®

Record 1,  Textual support,  English

Record number: 1, Textual support number: 1 CONT

The standard measurement for frame strength is a term known as "RBM" (Resistance to Bending Movement). The RBM is the yield strength of the frame material multiplied by the section modules of the frame rail. A typical yield strength of steel used in commercial truck chassis is 50,000 psi, and the section modules per frame is 13.3 to 13.4 inches cubed. Therefore, the RBM per rail is approximately 670,000 inch-pounds, with the RBM of the entire chassis frame (both rails) being double that, or 1,340,000 pounds.  4, record 1, English, - resistance%20to%20bending%20moment

Record number: 1, Textual support number: 2 CONT

Furthermore, a single frame in lieu of old double frames, such as those found in older dump trucks, saves 300-500 lb. in tare weight but still provides strong resistance to bending movement in the frame, which is essential when operating in a severe construction environment.  6, record 1, English, - resistance%20to%20bending%20moment

Record number: 1, Textual support number: 3 CONT

The 2000 Suburban ... modular frame ... Section modulus (in cubic inches) is up from 3.16 to 4.24 and the resistance to bending moment (in pounds/inches) goes from 104,000 to 140,000.  7, record 1, English, - resistance%20to%20bending%20moment

Record 1,  Textual support,  French

Record number: 1, Textual support number: 1 CONT

[...] balai de rue automoteur à quatre roues [...] CHASSIS : De type en «C» de 76 mm X 330 mm en acier à haute résistance et à faible teneur en carbone. Module de section : 16, 63. Résistance à la flexion : 831, 500 lbs/po.  2, record 1, French, - r%C3%A9sistance%20%C3%A0%20la%20flexion

Record number: 1, Textual support number: 2 CONT

Le dispositif de protection arrière doit avoir une résistance à la flexion au moins équivalente à celle d’une poutre en acier dont la section droite a un module de résistance à la flexion de 20 cm³.  3, record 1, French, - r%C3%A9sistance%20%C3%A0%20la%20flexion

Record number: 1, Textual support number: 1 OBS

flexion : Mécan. Courbure d’une pièce longue (poutre, barre...) sous l’action de forces perpendiculaires à l’axe longitudinal et appliquées en des points où la pièce n’est pas soutenue. Flexion plane. Module de flexion. Résistance à la flexion.  4, record 1, French, - r%C3%A9sistance%20%C3%A0%20la%20flexion

Record 1,  Textual support,  Spanish

Record 2,  Textual support,  English

Record number: 2, Textual support number: 1 CONT

... the secondary current passes from the coil into the center of the distributor cap where it is transmitted by a carbon brush to the center of the rotor.  2, record 2, English, - carbon%20brush

Record 2,  Textual support,  French

Record number: 2, Textual support number: 1 CONT

un balai de charbon conduit le courant au rotor de distribution  3, record 2, French, - balai%20de%20charbon

Record number: 2, Textual support number: 1 OBS

balai de charbon : terminologie retenue dans la version française du fichier stocks.  3, record 2, French, - balai%20de%20charbon

Record number: 2, Textual support number: 2 OBS

balai de charbon, balai de carbone : termes uniformisés par le CN.  4, record 2, French, - balai%20de%20charbon

Record 2,  Textual support,  Spanish